Copeland International is your supplier for Off Highway Allison Transmissions for Oil and Gas Well Service, Drilling, Plug and Abandonment, Stimulation, Fracking, Pump Down, Coiled Tubing, Workover.
Copeland Allison 6000 Series Transmission, S6600, S6610, S6620, CLT6061, CLT6062, M6600, M6610, M6620, CLT6063, CLBT6061
6000 Series Models Serviced: CLBT6061 CLT6061 M6600 M6610A M6610AR S6600 S6610H S6610HR S6610M S6610MR M6620 S6620 6061-4 CLBT6062 CLT6062 CLBT6063 CLT6063 CLBT 6061 CLT 6061 M 6600 M 6610A M 6610AR S 6600 S 6610H S 6610HR S 6610M S 6610MR M 6620 S 6620 CLBT 6062 CLT 6062 CLBT 6063 CLT 6063 M6610 S6610 Allison Transmission Models
CLBT6061 CLT6061 M6600 M6610A M6610AR S6600 S6610H S6610HR S6610M S6610MR M6620 S6620 6061-4 CLBT6062 CLT6062 CLBT6063 CLT6063 CLBT 6061 CLT 6061 M 6600 M 6610A M 6610AR S 6600 S 6610H S 6610HR S 6610M S 6610MR M 6620 S 6620 CLBT 6062 CLT 6062 CLBT 6063 CLT 6063
ALLISON CLT 6061 STRAIGHT THRU TRANSMISSION
Allison CLT6061-4 Straight Thru Transmission
Call Copeland Today - 1-800-966-9860 / 713-466-9838
The Allison CLT6061 or CLT6061-4 also referred to as CLT6061-ST Straight thru is a powerful transmission offering a large amount of input horse power and torque in a compact design with lockup (1 to 1 direct drive as opposed to using the converter), multiple torque converter ratios, 6 speed forward through a manual electric hydraulic both 12 volt and 24 volt control, in addition the most popular 6 speed manual hydraulic valve body providing ultimate control of the power behind the CLT 6061. Some applications run over 700HP with performance enhancements. Copeland International can supply manufacturers, suppliers or re-seller's, forwarding companies, procurement companies and most important end users here in the United States, Texas, Oklahoma, Arkansas, Louisiana, New Mexico, Mississippi, Alabama, Colorado, Pennsylvania, North Dakota, South Dakota, California, Wyoming, Illinois, Missouri, Ohio and far beyond to Canada, Europe the Middle East, Mexico and South America. All Transmissions are fully remanufactured Rebuilt and Dyno tested for 4-6 hours. This ensures you receive a fully functional and properly prepared product ready to go. This transmission is a staple in the oil and gas industry for high pressure and high volume pumps, mud pumps, drilling and workover support including; pump down, twin pumpers, high pressure pumping and well stimulation, coil tubing applications and nitrogen.
CLT6061 Allison Transmission is the staple point in the oilfield when it comes to Drilling Rigs, Workover Rigs, Pressure Pumping, Fracturing, Well Pumps, Well Service Pumps, Custom Applications, and Well Servicing industries With 6 speed manual hydraulic valve body or 6 speed manual electric, availability of transmission retarder feature, lockup feature (1:1, converter not being used), multiple Torque Converter ratios including TC680, TC682, TC683 (for performance), Transmission PTO pads on Top and Side. All Allison Transmissions Rebuilt, Refurbished, or Remanufactured by Copeland International are done so to the highest quality, ensuring that each unit will always have all new; seal and gasket kit, clutch plates, bearings, thrust washers, solenoids (where applicable) and sensors (where applicable). All hard parts (gears, shafts, planetary assemblies, carriers, converter section, drums, pistons, etc.) and main housings are meticulously inspected to ensure they meet factory wear limits and when replaced we use only the highest quality replacement parts. All Replacement parts meet or exceed OEM specifications (all part numbers, assembly numbers and model numbers are used for reference only). All Transmissions will have the most recent updates, High Cap or High Capacity Converter Pump in addition to drilled top disconnect for lube. Following rebuild completion each transmission is thoroughly Dyno tested with our state of the art Mustang Dyno powered by a Detroit Diesel 475 HP Series 60 Motor. With our specifically designed setup we are able to apply loads to the transmission simulating real world loads (Transmission Working Over a Well, Pumping Fluid down a hole, drilling a well, power units or power packages) to ensure proper operation when installed Our trained Dyno operators are able to test each unit for 4-6 hours (depending on transmission model) constantly monitoring pressures of main, splitter, lockup, converter and other vital information to qualify this as a Copeland Rebuilt Allison Transmission (Copeland Transmission). The process is finalized by Painting the unit to the customers desired paint color (depending on your service company we understand you wear your team colors proud!, let us make sure it's ready to match the fleet, just specify the color request to your sales person) packaged on a steel shipping skid, includes converter mounting gaskets, warranty paperwork, outfitted with a tag which supply's the pertinent unit information (serial number, assembly number, unit number, work order number) making future service simple identifying your specific assembly information. Product brochures, Service Manuals, Parts Manuals, Drawings and Additional product information is available upon request). Experience the Copeland International difference, we have Drop Box 5860 transmissions in stock on the shelf, ready to ship! Contact our experienced sales staff who can help you decide which transmission is right for your specific application. All Outright and Exchange Allison Transmissions supplied by Copeland International are done the same way every time. We never deviate from our methods and principals. Product longevity, performance and customer satisfaction are our main goals Call us at 1-800-966-9860 or 713-466-9838
CLT6061-4, CLT6061, CLT6061ST, CLT 6061, REBUILT, REMANUFACTURED, REMAN, USED, CORE